You are in the accessibility menu

Please use this identifier to cite or link to this item: http://acervodigital.unesp.br/handle/11449/16377
Full metadata record
DC FieldValueLanguage
dc.contributor.authorMachado, Ana Lucia-
dc.contributor.authorBreeding, L. C.-
dc.contributor.authorPuckett, A. D.-
dc.date.accessioned2014-05-20T13:46:19Z-
dc.date.accessioned2016-10-25T17:00:05Z-
dc.date.available2014-05-20T13:46:19Z-
dc.date.available2016-10-25T17:00:05Z-
dc.date.issued2005-08-01-
dc.identifierhttp://dx.doi.org/10.1016/j.prosdent.2005.04.017-
dc.identifier.citationJournal of Prosthetic Dentistry. St Louis: Mosby, Inc., v. 94, n. 2, p. 183-189, 2005.-
dc.identifier.issn0022-3913-
dc.identifier.urihttp://hdl.handle.net/11449/16377-
dc.identifier.urihttp://acervodigital.unesp.br/handle/11449/16377-
dc.description.abstractStatement of problem. Microwave irradiation has been suggested for denture disinfection. However, the effect of this procedure on the hardness and bond strength between resilient liners and denture base acrylic resin is not known.Purpose. This study evaluated the effect of water storage time and microwave disinfection on the hardness and peel bond strength of 2 silicone resilient lining materials to a heat-polymerized acrylic resin.Material and methods. Acrylic resin (Lucitone 199) specimens (75 X 10 X 3 mm) were stored in water at 37 degrees C (2 or 30 days) before bonding (n = 160). The resilient lining materials (GC Reline Extra Soft and Dentusil) were bonded to the denture base and divided into the following 4 groups (n = 10): Tests performed immediately after bonding (control); specimens immersed in water (200 mL) and irradiated twice, with 650 W for 6 minutes; specimens irradiated daily for 7 total cycles of disinfection; specimens immersed in water (37 degrees C) for 7 days. Specimens were submitted to a 180-degree peel test (at a crosshead speed of 10 mm/min) and the failure values (MPa) and mode of failure were recorded. Pretreatment and posttreatment hardness measurements (Shore A) of the resilient materials were also performed. Three-way analysis of variance, followed by the Tukey HSD test, was performed (alpha=.05).Results. The analysis revealed that, for all conditions, the mean failure strengths of GC Reline Extra Soft (0.95-1.19 MPa) were significantly higher (P<.001) than those of Dentusil (0.45-0.50 MPa). The adhesion of the liners was not adversely affected by water storage time of Lucitone 199 or microwave disinfection. All peel test failures were cohesive. There was a small but significant difference (P<.001) between the pretreatment (34.33 Shore A) and posttreatment (38.69 Shore A) hardness measurements.Conclusion. Microwave disinfection did not compromise the hardness of either resilient liners or their adhesion to the denture base resin Lucitone 199.en
dc.format.extent183-189-
dc.language.isoeng-
dc.publisherMosby, Inc-
dc.sourceWeb of Science-
dc.titleEffect of microwave disinfection on the hardness and adhesion of two resilient linersen
dc.typeoutro-
dc.contributor.institutionUniversidade Estadual Paulista (UNESP)-
dc.contributor.institutionUniversity of Mississippi-
dc.description.affiliationUNESP, Fac Odontol Araraquara, Araraquara Dent Sch, Dept Dent Mat & Prosthodont, BR-14801903 São Paulo, Brazil-
dc.description.affiliationUniv Mississippi, Med Ctr, Sch Dent, Jackson, MS 39216 USA-
dc.description.affiliationUnespUNESP, Fac Odontol Araraquara, Araraquara Dent Sch, Dept Dent Mat & Prosthodont, BR-14801903 São Paulo, Brazil-
dc.identifier.doi10.1016/j.prosdent.2005.04.017-
dc.identifier.wosWOS:000230994200010-
dc.rights.accessRightsAcesso restrito-
dc.relation.ispartofJournal of Prosthetic Dentistry-
Appears in Collections:Artigos, TCCs, Teses e Dissertações da Unesp

There are no files associated with this item.
 

Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.